Interlux Toplac Plus Marine PaintInterlux Toplac Plus delivers a hard, high-gloss polyurethane finish designed for topside applications above the waterline. This one-part marine paint features superior flow and leveling characteristics that produce smooth roller finishes without tipping. Apply it to hulls, decks, cabins, and trim using brush, roller, or spray methods. With coverage of 587 square feet per gallon, you’ll need 2-3 coats for optimal protection. The formula works with single-part primers, enamels, and polyurethanes while offering excellent UV resistance. Available in bright, crisp colors that maintain their appearance in harsh marine environments.Product Features:Hard, high gloss, one-part polyurethane finishExcellent flow and leveling characteristicsSmooth Roller Finish with no Tipping requiredTopside paint – Recommended for use above true waterlineFor use with single-part primers, enamels, or polyurethanesAvailable in a range of bright, crisp colorsSpecifications:Finish: High GlossApplication Method: Brush, roller or sprayNumber of Coats: 2 Minimum (only 1 may be needed for touch-up/repair)Coverage:587 sq. ft/gal per coatAssociated Products:Thinner/Cleaner2333N Reducing Solvent333 Brushing Thinner216 Special ThinnerHow To Apply Toplac PlusApplication Method: Brush, Roller, Spray Number of Coats: 2-3 Dry Film Thickness per Coat: 1-1.5 mils (2-3 wet mils)Coverage: 587 sq. ft/gal. Application Temp: 41F Min. / 95F Max.Thinning: Add 10% 2333N reducing solvent for brushes and 216 Special Thinner for sprayCleaner: 333 Brushing LiquidDRY TIMES: Temp Touch Dry Overcoating Substrate 95F 1 Hour 6 Hour Min / 24 Hour Max 77F 2 Hours 8 Hour Min / 2 Day Max 59F 3 Hours 16 Hour Min / 3 Day Max 41F 6 Hours 24 Hour Min / 4 Day MaxNote: Avoid applying late in the evening as condensation can cause a loss of gloss during overnight cure. Do not use in temperatures below 41 FSurface Preparation & ApplicationPreviously Painted Surface:In poor condition remove all previous coatings and prime the substrate, referring to the primer/undercoat technical datasheet for further preparation instructions.In good condition wash down with a suitable detergent, rinse with fresh water and allow to dryAbrade with 280 – 320 grit paper and remove sanding residueWipe with Brushing LIquid 333 and allow to dry completely.All Substrates:Prime with a suitable primer or primer/undercoatApplication Methods:Sand the undercoat smooth with 120 – 400 grit wet or dry paperRemove dust with a dust wipeApply 2-3 coats of Toplac Plus with 8-16 hours depending on ambient temperature (refer to the table above)Ambient temperatures should be between 41 F and 95 FDo not exceed 10% thinner by volumeClick here for Interlux Toplac Plus Topside Boat Paint Application InformationFrequently Asked QuestionsWhat is Toplac Plus used for, and where on the boat can it be applied?Toplac Plus is a topside paint for use above the waterline. It’s suitable for hulls, decks, cabins, and trim. It’s not an antifouling paint and should not be used below the waterline.Do I need to thin Toplac Plus, and which thinner should I use?Thinning depends on your application method. For brush or roller application, add up to 10% of Interlux 2333N Reducing Solvent. For spray application, use Interlux 216 Special Thinner instead. Do not exceed 10% thinner by volume regardless of method. For cleanup, use Interlux 333 Brushing Liquid.Does this paint require tipping after rolling, or will it self-level?One of Toplac Plus’s key advantages is that it doesn’t require tipping. Its flow and leveling characteristics produce a smooth finish straight off the roller, which is a me