Sea Hawk Cukote Bottom PaintSea Hawk’s Cukote Bottom Paint is a self-polishing ablative paint that provides multi-season protection. Cukote Bottom Paint has a high load of cuprous oxide that makes this formula a top performer even in the most severe fouling areas. Due to its ablative and self-polishing nature, there is no buildup of bottom paint over time. The underwater surface of your hull remains clean and smooth, making this an ideal bottom paint for fast moving vessels. The copolymer in Cukote can withstand removal from water without affecting its antifouling properties. Sea Hawk’s Cukote is the premium self-polishing antifouling paint that has established the standard in the industry.Features:Semi-Hard, self-polishing ablative finishMulti-season performanceRemoving boat from water does not affect antifouling propertiesEffective below the waterline on fiberglass, steel, and wood vesselsNo TBT (organotin compounds)47.5% Cuprous oxideSpecifications:Finish:Semi-GlossCopper Content:47.57%VOC:398 grams/literCoverage:346 sq. ft.Number of Coats:2Colors Available:3445-Black, 3441-Red, 3442-Blue, 3434-TealPack Size:1 US GallonHow to Apply Sea Hawk Cukote Bottom PaintSea Hawk Cukote Bottom Paint is easily applied by brush, roller, or spray. When rolling, use only a high-quality short nap 3/8 roller cover. Apply using thin coats. For the smoothest possible finish, thin the paint approximately 10% using water. Cukote has a tendency for settling to occur, especially if the paint has been on the shelf for several months. Thoroughly mix the paint before using. Before using, check the sides and bottom of the can to make sure all the pigment has been mixed in.Finish: Semi-GlossCoverage: 320 Sq FtApplication Method: Bursh, Rolling, Airless SprayerMaximum Roller Thickness: 3/8 NapNumber of Coats: 2Wet Film Thickness: 5.0 milsDry Film Thickness: 2.2 milsApplication Temp: 50 F Min/ 95 F MaxThinner: Maximum 10% Sea Hawk 2031 ReducerDrying TimesSubstrate Temp.Touch Dry Minimum Overcoat Time Minimum Launch Time 73F 2 hours 1 hour 12 hours95F 1 hour 1 hour 12 hoursSurface Preparation and ApplicationPreviously Painted SurfacesKnown Compatibility of existing antifoulantPower wash to remove any loose paint or other contaminants.Scuff sand with 80 grit sandpaper, remove all residue and let dry.Apply minimum 2 coats of Cukote. Allow 3-6 hours between coats and a minimum overnight dry.Unknown Compatibility of existing antifoulantPower wash to remove any loose paint or other contaminants.Scuff sand with 80 grit sandpaper, remove all residue and let dry.Apply 1 coat of 1277 Barrier coat primer or 1283 Island PrimerApply minimum of two coats of Cukote. Allow 3-6 hours between coats and a minimum overnight dry.Poor condition of existing antifoulantIf previous coating is cracking, peeling, or flaking strip the antifoulant with stripper, sanding, or commercial blasting.Once stripped refer to the Bare Fiberglass Application Guidelines.Bare FiberglassTo prepare the surface it is important to remove all contaminants first. Scrub the surface with detergent soap and a stiff brush.Using either S-80 Wax N Grease Killer or S-90 De-Wax Etch & Cleaner scrub the surface and rinse thoroughly.Sand to a uniform dull looking surface with 80-100 grit sandpaper and rewash with S-80 Wax and Grease Killer or S-90 De-Watch Etch & CleanerOnce cleaned and sanded, seal the surface with 2-3 coats of Tuff Stuff. Apply the second coat once the first has a tacky feel.Apply minimum of two coats of Cukote. Allow 3-6 hours between coats and a minimumSanding Method:Sand to a uniform dull looking surface with 80-100 grit sandpaper